 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| K1523BA Series K1523BA Series 14 DIP, 5.0 Volt, TTL/HCMOS, VCXO THIS PRODUCT IS NOT Voltage Controlled Crystal Oscillators RECOMMENDED FOR NEW DESIGNS. PLEASE REFER TO THE MV PRODUCT SERIES. APPLICATIONS Phase-Locked Loops (PLL's); Clock Recovery; Reference Signal APPLICATIONS Phase-Locked Loops (PLL's); Clock Tracking; Reference Signal Recovery; Synthesizers; Frequency I C A L S P E C I F I C AT IFrequency Modulation/Demodulation Tracking; Synthesizers; O N S 25.0 to 35.0 Modulation/Demodulation MHz Frequency Range K1523BA 25.0 to 35.0 MHz Frequency Control Voltage 0.5V to 4.5V Range 0.5V to 4.5V Control Voltage 35 to 33 25ppm33.1 to Stability 25ppm < 26 Variety of Deviation Sensitivity Options Stability Variety of Deviation Sensitivity Options Deviation Range, Vc Range, etc. - 85C Operating Temperature -40C to Consult Factory) -40C to 85C Operating Temperature 100 190 < 10 Model > 20KHz Frequency Range (MHz) 2.5 Frequency Range (MHz) Model Input Current (mA) Deviation (ppm) K1523BA Series Crystal Oscillators Voltage Controlled Voltage Controlled Crystal Oscillators K1523BA Series LEC I RICAL SP E L E C T R I C A LES P E CTF I C AT I O N S E C I F I C AT I O N S K1523BA 25 to 33 < 26 K1523BA 33.1 to 35 25 to 33 33.1 to 35 < 26 Input Current (mA) 0.5 to 4.5 Frequency Control Function Frequency Control Function Positive >Minimum 10KHz 50K @ Deviation (ppm) Minimum Maximum (For Custom Deviation Range, Vc Range, etc. - Consult Factory) 100 190 < 10 > 20KHz 2.5 0.5 to 4.5 Positive > 50K @ 10KHz (For Custom Deviation Range, Vc Range, etc. - Consult Factory) 100 190 < 10 > 20KHz 2.5 0.5 to 4.5 Positive 40 Maximum Calibration, Temperature, Voltage, Load and Aging Linearity (%) Modulation Bandwidth (3dB) Linearity (%) 40 25 50 Nominal Control Voltage (V) Bandwidth (3dB) Modulation 55 Control Voltage Range (V) Control Voltage (V) Nominal Transfer Function Control Voltage Range (V) Input Impedance o -40oC to +85 C Transfer Function Frequency Stability (ppm) Input -40oC to +125oC Impedance 5% 40/60 -40oC to +85oC <10 Hz 0Hz Hz KHz KHz Overall o o o0 C to +70 C Overall Frequency Stability (ppm) 0oC to +70oC > 50K @ 10KHz Inclusive of Calibration, Temperature, Voltage, Load and Aging 25 50 Inclusive of Calibration, Temperature, Voltage, Load and Aging 55 25 40 55 -40oC to +85oC -40oC to +125oC -65 -95 -120 oC -40oC to +8550 oC to +125oC -40 Temperature Range ( C) -65 -40oC to +85oC Operating -95 Storage Temperature Range (oC) -120 Supply Voltage (V) Operating -140 Symmetry (%) CMOS/TTL Storage -150 Start Up Time (ms) +5.0V 5% 40/60 <10 10Hz 100Hz 1KHz 10KHz 100KHz Supply Voltage (V) SSB Phase Noise (dBC/Hz) +5.0V 5% Symmetry (%) CMOS/TTL Offset from Carrier 40/60 <10 -65 -95 -120 -140 -150 NG GUIDE Start Up Time (ms) SSB Phase Noise (dBC/Hz) Offset from Carrier 10Hz 100Hz 1KHz 10KHz 100KHz -140 -150 0C Operating Temp. C Operating Temp. Please see www.mtronpti.com for our complete PA R T N U M B Contact us for G application Phone: 847.451.1000 Fax: 847.451.7585 offering and detailed datasheets.E R I N G your U I D E specific requirements: MtronPTI 1-800-762-8800. K1523BA X - Specify Frequency "Blank" = 0C to 70C Operating Temp. MtronPTI reserves the right to make changes to the product(s) and service(s) described herein without notice. No liability is assumed as a result of their use or application. "M" = -40C to +85C Operating Temp. PA R T N U M B E R I N G G U I D E hamptech.com K1523BA X - Specify Frequency "Blank" = 0C to 70C Operating Temp. Revision: 03-09-07 K1523BA Series 14 DIP, 5.0 Volt, TTL/HCMOS, VCXO K1523BA Series PIN 1 7 8 14 FUNCTION Voltage Control Gnd/ & Case Gnd Output + VCC THIS PRODUCT IS NOT RECOMMENDED FORVoltage Controlled Crystal Oscillators NEW DESIGNS. PLEASE REFER TO THE MV PRODUCT SERIES. SHIPPING TUBE CROSS SECTION OUTPUT WAVEFORM TEST CIRCUIT DIAGRAM MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS TEST METHODS Temperature Cycle Mechanical Shock Vibration Humidity Steady State Thermal Shock Electrostatic Discharge Solderability Hermeticity Resistance to Soldering Lead Integrity Marking Permanence Life Test REFERENCE PROCEDURES MIL-STD-833, Mtd 1010, Cond. B MIL-STD-202, Mtd 213, Cond. D MIL-STD 202, Mtd 204, Cond. B MIL-STD-202, Mtd 103 MIL-STD-883, Mtd 1011.7 Cond. A MIL-STD-883, Mtd 3015 Class II MIL-STD-883, Mtd 2022.2 MIL-STD-883, Mtd 1014.8, Cond. A1 DESCRIPTION -55C to +125C; Air-to-Air; 100 cycles; 10 min. dwell 500 g's 10-2000 Hz; 0.06 inch; 15g; 3 planes 40C; 90%-95% R.H.; 56 days 100C to 0C; Water-to-Water; 15 cycles 2 KV to 4 KV Threshold Solder dip; Meniscograph Criteria Mass spectro. 2 x 10-8 atmos. CC/sec He 240C; 10 seconds: 1 inch/sec. MIL-STD-202, Mtd 210A, Cond. C MIL-STD-883, Mtd 2004.5, Cond. A, B1 Lead tension & bend stress MIL-STD-883, Mtd 2015.8 MIL-STD-883, Mtd 1005.6 Resistance to solvents 125C, powered, 1000 hours minimum MtronPTI reserves the right to make changes to the product(s) and service(s) described herein without notice. No liability is assumed as a result of their use or application. 2553 N. Edgington complete Franklin Park, IL 60131 Fax: 847.451.7585 Please see www.mtronpti.com for ourStreet, offering and detailed datasheets. Contact Phone: 847.451.1000requirements: MtronPTI 1-800-762-8800. us for your application specific 800-888-1499 or www.champtech.com Revision: 03-09-07 |
Price & Availability of K1523BA07
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |